2020 Mustang Track Loaders 2550RT

Information

2020 Mustang Track Loaders 2550RT

Features may include:

Performance

The Mustang 2550RT Track Loader was designed from the ground up...

Tier IV-certified Deutz diesel engines provide 74.3 hp (55.4 kW)

Rated operating capacity at 35% of 2550 lbs (1157 kg), which can safely pick-up and operate to it's full potential.

Flush rear door and angled rear towers provide tight rear clearance radius and excellent visibility.

243 ft-lbs (330 Nm) of useful torque to assist the engine power output.

Operator's Cab

The extra-large, state-of-the art operator’s station on the 2550RT Track Loader is designed for optimal operator comfort resulting in more productivity.

The hydraulic-pilot controls are mounted to the seat, so they move with the operator that gives a true 1:1 proportional control over the drive system.

All-New seat-mounted pilot control system - redesigned cab mount the controls to the seat, providing added leg room and less arm fatigue during operation.

Hydraloc™system applies the parking brake whenever the operator raises the restraint bars, leaves the operator's seat, open the door or switches off the ignition.

Standard, selectable 2-speed drive motors, horn and backup alarm.

Pilot Hydraulic transmission with direct engine coupling delivers operating efficiency while our actuation valve technology keeps the power flowing. This feature monitors and adjusts the hydrostatic drive pump to produce the ideal tractive effort.

Easy to use, multi-function display incorporates all warning & operation lights and machine configuration screens. Single button allows for simple scrolling and selection of various display functions

Controls

Controls on the 2550RT Track Loaders are ergonomically designed to reduce operator fatigue, increase productivity and improve versatility.

The IdealAccess™ Door is a patented design featuring a low clearance door that delivers cab-to-canopy versatility and easy access.

Level II ROPS/FOPS provides the highest level of safety protection for an operator in a roll over or falling object situation.

Our all new seat-mounted pilot control system has redesigned the cab by mounting the controls to the seat. This provides added leg room and less arm fatigue during operation.

Tilt out foot feature allows for best-in-class foot well clean out and provides easy access to the fuel tank and other components under the cab.

Excellent sight lines from all sides for safe and precise placement of loads and reduced jobsite incidents. A high-mounted seat provides an excellent vantage point to the attachment and cutting-edge.

New "glove friendly", weather proof push style buttons with an automotive design and feel

Photos

Highlights

  • Norfolk, Virginia
  • 2020
  • Mustang
  • Track Loaders 2550RT
  • Axial Piston
  • Available
  • Bucket: 83.9" (2131 mm)
  • to Hinge Pin - Fully Raised: 128" (3251 mm) | Dump Height - Fully Raised: 98" (2489 mm) | Specified Height: 67.7" (1720 mm) | Reach at Specified Height: 31.3" (795 mm) | Dump Angle at Specified Height: 66.8° | Maximum Rollback at Specified Height: 66.8° | Grouser Height: 1" (25 mm)

Specifications

  • 2020
  • Mustang
  • Track Loaders
  • 2550RT
  • Compact
  • Deutz/ TD 3.6 L4 Tier IV
  • 4
  • Turbo
  • 221 cu.in. (3.621 L)
  • 4
  • Net Horsepower (kW) @ 2500 rpm: 70.7 hp (52.7) @ 2300
  • Peak Torque (Nm) @ 1600 rpm: 243 ft.-lbs. (330) @ 1600
  • Axial Piston with Planetary Reduction
  • Axial Piston
  • 12V/120A
  • Drawbar Pull / Tractive Effort: 12,453 lbs. (5649 kN) | Bucket Breakout - Tilt Cylinder: 8,384 lbs. (3803 kg) | Bucket Breakout - Lift Cylinder: 7,437 lbs. (3373 kg)
  • 5.2 psi (0.36 bar)
  • Ground Speed - Single Speed: 5.3 mph (8.5 km/hr) | Ground Speed - Two Speed: 7.5 mph (12.1 km/hr)
  • Auxiliary Hydraulic Flow - Rated Speed: 29.07 gpm (110 L/min) | High-Flow Hydraulic Flow - Rated Speed: 37.7 gpm (142.7 L/min)
  • Reach - Fully Raised: 34.5" (876 mm) | Dump Angle - Fully Raised: 41° | Maximum Rollback Angle - Fully Raised: 102.5° | Maximum Rollback Angle at Ground: 30° | Carry Position: 8.2" (208 mm) | Maximum Rollback Angle at Carry Position: 31.6° | Digging Position - Below Ground: +0.5" (13 mm) | Angle of Departure with Standard Counterweight: 25° | Track Gauge: 51.7" (1313 mm) | Crawler Base: 61.5" (1562 mm) | Clearance Radius - Front with Bucket: 98.4" (2499 mm) | Clearance Radius - Rear with Standard Counterweight: 70.7" (1796 mm) | Angle of Approach: 90°
  • Overall Operating Height - Fully Raised: 168" (4267 mm) | at ROPS: 83.1" (2111 mm)
  • to Hinge Pin - Fully Raised: 128" (3251 mm) | Dump Height - Fully Raised: 98" (2489 mm) | Specified Height: 67.7" (1720 mm) | Reach at Specified Height: 31.3" (795 mm) | Dump Angle at Specified Height: 66.8° | Maximum Rollback at Specified Height: 66.8° | Grouser Height: 1" (25 mm)
  • with Bucket - Standard Counterweight: 157.8" (4008 mm) | without Bucket - Standard Counterweight: 126.8" (3221 mm)
  • 12.3" (313 mm)
  • 17.7″ (450 mm) | Track Shoe Width: 17.7" (450 mm)
  • Less Bucket: 69.5" (1765 mm)
  • Bucket: 83.9" (2131 mm)
  • Operating Capacity at 35% of Tipping Load: 2,550 lbs. (1157 kg) | Operating Capacity at 50% of Tipping Load: 3,643 lbs. (1652 kg) | Tipping Load: 7,286 lbs. (3305 kg)
  • Pump: 11 qts. (10.4 L)
  • Tank: 32 gal. (121.1 L)
  • Reservoir Tank: 13.8 gal. (52.2 L)
  • 6.1 gal. (23.1 L)
  • 11,600 lbs. (5260 kg)
  • Roller Type: Steel
  • Rubber | Rollers: 5